tongue and groove roof decking installation

Installing Floor Joists, Tongue and Groove…

Bob helps contractor Bob Ryley install 4x10 douglas fir floor joists, and also put in 2 x 6 spruce tongue-and-groove decking on the second floor.

Installation Instructions - Homasote

EasyPly Roof Deck is made of various plies of high density. Homasote structural . Long edges are T&G with a V -groove on the ceiling side. .. Install. Roof Decking panels with long edges at right angles to rafters, starting at low point of framing, with tongue of T&G pointing to ridge and finish (ceiling) side down on rafters.

2x6 t&g roof deck - JLC-Online Forums

Looking at using 2x tongue and groove for decking. but need info on allowable spans, best practices, good suppliers, etc. .any suggestions? . That manufacturer will likely have some load tables and installation materials/instructions for their decking, and you should be able to get them, either the web or.

Tongue and Groove Installation on a Timber Frame Home -…

2 Sep 2016 . while I can appreciate the outside tongue and groove I would have saved myself the work and kept it safe by cladding the outside with plywood (as its all covered with roofing anyway) then from the inside put a good 2 inches of insulation first with a slight gap then put an inner cedar tongue and groove of.

Roof Sheathing Materials | Roof Decking Guide -…

Tongue and Groove. Commonly used as roof sheathing where a ceiling will not be installed and they will be visible from inside the house, such as across beams in a vaulted ceiling. Wood is an excellent insulator and in moderate climates no additional rigid insulation on the roof is necessary. The boards can be painted,.

Roof Sheathing - Free-Ed.Net

Upon completing this section, you should be able to identify various types of roof sheathing and describe their installation requirements. .. INSTALLATION.—Wood fiber roof decking is laid with the tongue-and-groove joint at right angles to the support members. The decking is started at the cave line with the groove edge.

easy t&g roof

plywood tongue and groove product with proven performance. The precision-engineered tongue and groove dimensions of EASY T&G ROOF are internationally patented* and designed to: be the finest structural panel on the market today. 0 Enable fast, problem-free installation. Richply offers builders all the proven.

Roofing: Why do we need plywood over our old solid…

It used to be standard to use shiplap, 1″ boards, tongue & groove, or other boards for the roof deck. These 8 to 12-inch wide boards were nailed . So, anytime your board-decked roof is torn off and you want to install composition shingles be sure to lay down solid sheathing first! Please contact Sharp Roofing for a free roof.

Tongue and Groove Roofing – Romtec Inc.

Romtec uses tongue and groove (T&G) timber decking as the standard roof decking material on every building. T&G roof decking provides roofs with several . When installing a building, choosing the proper material for roof decking can eliminate a lot of concerns down the road. Compared to plywood, T&G roof decking is.

Engineered Wood Construction Guide

to complete roof deck installation prior to applying roofing. APA RATED. SHEATHING. 1/8" spacing is recommended at all edge and end joints unless otherwise indicated by panel manufacturer. Stagger end joints. (optional). Panel clip or tongue-and-groove edges if required. Asphalt or wood shingles or shakes.

Metal Roof Installation Manual - Metal Construction…

ROOF DECK SUBSTRUCTURES. CHAPTER 6. 6. INTRODUCTION. The roof substructure is an integral part of the roof system. It lies just beneath the metal .. Laminated boards often have a tongue and groove edge for installation. Wood plank decks should have a minimum thickness of one inch. Fastener type and.

2 x 6 TIMBER DECKING - Structural Wood Systems

It is machined with a single tongue-and-groove, a . American Institute of Timber Construction standards for tongue-and-groove heavy timber decking. S.P.I.B. No. 1 Grade lumber decking is standard and is used where . This decking is to be installed with tongues upward on sloped or pitched roofs and outward from.

Standard for Tongue-and-Groove Roof Decking - American…

Standard for Tongue-and-Groove Roof Decking, AITC 112-93 7. 2 ft minimum end joint spacing. Figure 7. Controlled Random Layup. (Two inch decking). Three and Four Inch Decking. There shall be a . quality when appearance requirements are less critical. 8. WEIGHTS OF INSTALLED DECKING (See Table 2, page 10).

Lock-Deck Installation

The nailing of panel edges is the same as for panels installed over joists. The Lock-Deck™ provides the required blocking. Lock-Deck™ laminated roof or floor decking in 3", 4", and 5" thicknesses may be designed to resist lateral forces when a 3/8" bead of 3M adhesive No. 5200 is applied on top of the tongue-and-groove.

The Long and Short of Wood Roof Systems -…

30 Sep 2014 . 2 “Tongue and Grove Roof Decking”. Lumber Decking. Code Acceptance for 2, 3 and 4 inch thick Tongue. & Groove Lumber Decking per IBC 2012 2304.8 .. Typical for large, low slope, roof structures. How is a Panelized Roof Constructed? 1. Column erection. 2. Girders placement. 3. Purlin installation.